Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Tujunga Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco chimney cleaning service in Tujunga, CA. That means we sweep, inspect, repair and install Gelco caps, dampers and insert venting without any manufacturer authorization or endorsement, and we tell you plainly which Gelco component is likely at fault before anyone arrives. In a foothill town where the stakes run higher than tidiness, that clarity matters. Our technicians have up to 9 years of experience, and they’ve seen how Gelco’s factory-built approach to caps, dampers and multi-flue assemblies behaves in real homes across Tujunga, from the canyon edges up toward the national forest boundary. One call covers diagnosis and repair: we find it, we fix it. Call (844) 968-2733. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Chimney Sweep Tujunga for Your Gelco Chimney Cleaning?
Our technicians work on Gelco systems every burning season, so the failure patterns are familiar: corroded welds on top-mount cap screens, dampers that seize at the pivot, frame bolts that back out over time. Familiarity with those parts is what lets us match you to the right independent local pro for inspection, sweeping and repair, instead of guessing at what’s going wrong.
We choose quality parts that fit Gelco equipment. That means genuine Gelco caps, dampers and screens when they’re available for a direct fit, and quality aftermarket stainless equivalents where OEM parts are discontinued or overpriced. We’re not a Gelco dealer and we don’t claim factory training or certification. We’re an independent shop, and that independence is the point: nobody here is under pressure to sell you a particular part number.
Warranty-safe service matters just as much. When we pull a cap or work around an insert, we do it in ways that protect the surrounding assembly, use fasteners and sealants rated for the application, and document what we found with camera inspection and a photo report you keep. If a manufacturer’s warranty question ever comes up, you have evidence of what was done and why. That’s how a Gelco chimney cleaning visit in Tujunga should work.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Tujunga
- Cap screens corroding or tearing at the spot welds. This is the failure Gelco owners report most. The screen mesh holds up, but the weld points where it meets the frame rust through first, and a torn screen turns the cap into an open door. Birds nest in the flue, debris collects, and creosote builds faster because airflow is compromised. In Tujunga, where the dry season runs long, a rarely used fireplace with a compromised screen is exactly where creosote turns tarry.
- Damper plates warping or seizing at the pivot. A Gelco damper that won’t close all the way leaves the fireplace open to the outside air when the fire is cold. You lose heat, you gain downdraft, and the seal is gone. The pivot is usually the culprit, not the plate, which is why we check the hinge point before recommending replacement.
- Multi-flue cap frames loosening from their mounting bolts. Wind-driven weather and seasonal movement back those bolts out over time. Once the frame lifts, water tracks down between the flues and stains the firebox. Foothill homes here take stronger wind loads than valley floor properties, and older canyon homes often have no cap at all, so a loose frame gets worse fast.
- Venting and cap interface gaps on Gelco fireplace inserts. An insert relies on a sealed path from the unit through the venting to the cap. A gap at that interface lets downdraft in, which shows up as smoke spillage into the room and soot accumulating ahead of schedule. It’s a fit problem, and it’s fixable without replacing the insert.
- Debris-packed caps after a red-flag warning. Tujunga’s brushy terrain and Santa Ana winds drive ash, leaves and ember-borne debris into cap assemblies. A plugged screen blocks draft and creates a spark-emission risk on a home that backs onto dry hillside. Cleaning here is as much about fire-hardening the home against ember intrusion as it is about sweeping soot.
Gelco Parts & Our Repair-vs-Replace Approach
We use genuine Gelco caps, dampers and screens when available for a direct fit, and quality aftermarket stainless equivalents where OEM parts are discontinued or overpriced. We don’t stock OEM or genuine Gelco parts, and we won’t tell you we do. What we do is source the right component for your assembly and install it correctly.
The repair-versus-replace call comes down to where the metal is failing. If a cap frame or damper is only rusted at the fasteners, repair and reseal first. That’s usually the honest answer, and it’s cheaper. Full replacement makes sense only when the metal itself has lost structural integrity, the welds are gone across the frame, or the screen is torn in a way that can’t be re-secured. You get the camera evidence and a photo report so you can see the difference yourself. Nothing gets recommended without it, and we’ll say plainly when work can safely wait.
If you’re unsure which side of that line your Gelco cap is on, call (844) 968-2733 for a free estimate.
Our Gelco Service Process – Step by Step
- 1
Diagnosis. We start with a camera inspection of the flue and a close look at the cap, screen, damper and insert interface. You see the footage and the photos. This is where we identify whether the problem is a torn screen, a seized pivot, a loose frame or a venting gap.
- 2
Repair or install. Based on what the inspection shows, we repair what’s sound and replace what isn’t, using parts sized to your Gelco assembly. Hardware and sealant are matched to the application so the fix holds through the season.
- 3
Test. We check draft, confirm the damper seats and seals, and verify the cap is properly seated on the crown with no gaps where water or birds can get in. If the insert interface was the issue, we test that the venting path is sealed end to end.
- 4
Warranty and documentation. You receive the photo report and a written scope of what was done. If a warranty question comes up later, you have the record.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in Tujunga
We service and install the kinds of Gelco products Tujunga homeowners actually have on their roofs and in their fireboxes. That includes top-mount multi-flue chimney caps, stainless single-flue caps with spark screens, factory-built fireplace inserts and their venting kits, and replacement dampers and cap-screen assemblies. Spark screens get particular attention here, because ember intrusion is a real concern on hillside and canyon properties with dry brush close by.
Our cap and crown work is a specialization in its own right. Caps are where most water intrusion and wildlife entry starts, and a Gelco assembly fitted correctly prevents both. We also handle the chimney repair and fireplace repair work that turns up once the cap comes off and the flue is visible. If you’re choosing a cap for a new installation, we’ll talk through fit and sizing against your flue configuration rather than handing you a generic cover.
We Also Service These Brands
Gelco is one brand in a broader toolkit. We also work with DuraFlex liner systems and HeatShield resurfacing, along with Olympia Chimney, Famco and Copperfield components. That range means we’re not locked into one manufacturer’s answer when a different product fits your chimney better. If your home has a mix of brands, or you’re not sure what’s up there, we’ll identify it during inspection.
FAQs – Gelco Chimney Cleaning Service in Tujunga
No. We are an independent service provider with no affiliation, authorization or endorsement from Gelco. We work on Gelco products every season and we’re candid about that independence, because it means our recommendations come from what we see in the flue, not from a manufacturer relationship. Call (844) 968-2733 for a free estimate.
Usually yes. We source genuine Gelco caps when they’re available for a direct fit, and quality aftermarket stainless equivalents where OEM parts are discontinued or overpriced. If only the fasteners are rusted, we repair and reseal the existing frame first. Call (844) 968-2733 for a free estimate.
Not always. A damper that won’t seal is often seizing at the pivot rather than failing in the plate itself, and a pivot repair can restore the seal without a full replacement. We check the hinge point first and only recommend a new damper when the plate or frame is genuinely warped or cracked. Call (844) 968-2733 for a free estimate.
No. A factory-built insert relies on a sealed venting path from the unit through the venting kit to the cap, so service includes checking that interface for gaps that cause downdraft and smoke spillage. Sweeping is part of it, but the venting and cap connection get equal attention. Call (844) 968-2733 for a free estimate.
Once a year is the usual baseline for an actively used fireplace, and more often if you burn heavily or notice draft problems. In Tujunga, the long dry season means creosote in a rarely used fireplace can become tarry and highly flammable, so annual inspection matters even in years with light burning. Call (844) 968-2733 for a free estimate.
A typical job starts with rust streaks down the chimney and birds getting into the flue. On inspection, the cap screen is often torn at the welds and the frame bolts have loosened. A qualified local sweep removes and disposes of the old cap, checks the flue tiles for debris and creosote that got past the screen, sweeps as needed, then fits a correctly sized stainless replacement cap sealed to the crown. On canyon and hillside homes, adding a spark arrestor as part of that work is standard. Call (844) 968-2733 for a free estimate.
Independent service does not automatically void a manufacturer warranty, but the terms are set by the manufacturer, not by us. We use parts sized and rated for the application, document the work with a photo report, and keep a written scope so you have a record if a warranty question ever arises. Call (844) 968-2733 for a free estimate.
Pricing is set per job by a written estimate, and the estimate is free. A standard sweep and inspection is one line item; cap, damper and insert-venting repairs are quoted separately based on what the camera shows. You’ll know the scope and the price before any work begins, and nothing is recommended without photo evidence you can see. Call (844) 968-2733 for an exact quote.
Book Your Gelco Service in Tujunga, CA
Whether your Gelco cap is rusted through, your damper won’t seal, or you just want the flue swept and inspected before the burning season, one call covers it. Call (844) 968-2733. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free, the price is set per job in writing, and camera inspection with a photo report is included.
Written by the team at Chimney Sweep Tujunga.