Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Tujunga?
Chimney liner and rebuild work in Tujunga typically runs $2,200 to $8,500, with most full stainless liner installs landing between $2,800 and $5,200 and partial chimney rebuilds (crown, flashing, and upper courses) between $1,800 and $6,500. A full top-to-bottom rebuild on a heavily deteriorated masonry stack can push past $10,000, and the only way to know which number applies to your chimney is a documented inspection with photos and a written scope.
We handle this as a full-system job: inspection findings, liner sizing, crown and cap work, and the repair itself in one scope. No hand-off. Call (844) 968-2733 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Most liner installs in Tujunga: $2,800-$5,200 (stainless, insulated, sized to the appliance).
- Cast-in-place resurfacing (HeatShield): $1,600-$3,800 for a mid-length flue.
- Partial rebuild with new crown: $1,800-$6,500.
- Full chimney rebuild from the ground up: $6,000-$10,000+.
- The written estimate sets the final price. Free estimates are standard, no trip charge.
Chimney Liner & Rebuild Cost Breakdown (2026)
The ranges below reflect typical Tujunga jobs, meaning single-story and split-level homes in the foothill neighborhoods with masonry fireplaces and mid-length flues. Two-story stacks, offset flues, and unusual terminations scale upward.
| Line Item | Typical Range (Tujunga, 2026) | Notes |
|---|---|---|
| Level 2 inspection with photos | $250-$450 | Camera sweep of the flue, crown and cap condition, documentation |
| Sweep before liner work | $180-$350 | Required prep on any flue getting lined or resurfaced |
| Stainless liner, installed (DuraFlex or Olympia Chimney) | $2,800-$5,200 | Insulated, sized to the fireplace or insert; includes cap and top plate |
| HeatShield cast-in-place resurfacing | $1,600-$3,800 | Mid-length flue, good structural masonry, no rebuilding needed |
| Chimney crown rebuild | $650-$1,400 | Pour or form a new crown with proper slope and overhang |
| Chimney cap (Gelco or Famco) | $180-$500 | Fitted, manufacturer-grade; single-flue to multi-flue sizes |
| Masonry repointing, upper courses | $800-$2,500 | Depends on course count and access |
| Partial rebuild (crown, flashing, upper courses) | $1,800-$6,500 | The most common rebuild scope |
| Full rebuild, ground to top | $6,000-$10,000+ | When the stack itself is failing, not just the top |
| Firebox or damper repair | $400-$1,500 | Handled under our fireplace repair work |
What drives the number up or down? Three things, in order of impact. First, the flue itself: a straight, square, correctly sized flue takes a liner cleanly, while offsets, ovalizing, and pre-existing liners that need removal add labor. Second, access: a stack on the low side of a pitched roof in the foothills is easier to work than one on a steep gable end, and access scaffolding or roof anchors add cost. Third, what the inspection finds: hairline cracks in the flue tile that stop at resurfacing versus spalled brick that means actual masonry comes out and goes back. The written estimate lays out which category your chimney falls into, item by item, before any work starts.
What Affects Chimney Liner & Rebuild Pricing in Tujunga
- Flue condition and tile integrity. A flue with intact tiles and no gaps is a candidate for cast-in-place resurfacing. One with cracked, spalled, or missing tiles needs a stainless liner or rebuild. The inspection determines which, and that decision is the single biggest line item on the estimate.
- Liner diameter and appliance type. A wood-burning insert needs a specific flue size for the draft to work. Oversizing a liner to save money on materials is a common shortcut that causes smoking and poor draft. We size the liner to the appliance, which sometimes means a slightly larger liner than the cheapest option on the shelf.
- Crown and cap condition. The crown and cap are where water gets in. In Tujunga, a cracked crown left alone through a wet winter shows up as interior staining and rusted dampers by spring. We address the crown and cap on the same visit as the liner work, since pulling both apart separately costs more than doing them together.
- Roof pitch and access. Foothill homes sit on grades, and roof access ranges from a walk-up to a steep pitch that needs anchors. Access affects labor hours, and labor hours affect the number.
- Rebuild scope: partial versus full. A partial rebuild (crown, flashing, upper courses) is roughly half the cost of a full rebuild. The difference is whether the failure is concentrated at the top or runs through the whole stack. A camera inspection tells you which before anyone quotes.
- Material grade. We install DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield because they are the professional-grade options in this trade. A cheaper liner on paper often means a shorter service life and a second install sooner. We quote the materials we will actually put in.
For the full picture of how liner replacement and rebuilds fit together structurally, see our chimney liner & rebuild page.
How to Save on Chimney Liner & Rebuild
The biggest savings in this trade come from catching problems early and combining visits. A crown repair done at $650-$1,400 today is a much smaller bill than the interior water damage and rebuild that follows a cracked crown through a couple of rainy seasons. Here is what actually helps.
- Get the inspection before you buy anything. A level 2 inspection with photos ($250-$450) tells you exactly what needs doing and in what order. Skipping it and going straight to a liner quote risks paying for a liner on a chimney that needs masonry work first.
- Combine liner, crown, and cap into one scope. These are separate line items on paper, but a single visit for all three is cheaper than three separate appointments with setup repeated each time.
- Resurface when the masonry allows it. HeatShield cast-in-place resurfacing ($1,600-$3,800) is often a fraction of a full liner install and rebuild when the flue is still structurally sound. Not every chimney qualifies, but the inspection answers that.
- Fix the water intrusion first. A new crown and a fitted Gelco or Famco cap stop the water that is causing the damage in the first place. Liner work behind an open chimney top is a repair that will be repeated.
- Get a written scope, not a verbal number. A written estimate with each line item priced is the only way to compare quotes fairly. A single lump-sum number hides what is and is not included.
- Deal with the fireplace and the flue together. If the damper or firebox needs work, it makes sense to price it on the same estimate as the liner. The flue is open during liner work, so access is already there.
Free estimates are standard with every job, and there is no trip charge. Call (844) 968-2733. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
FAQs – Chimney Liner & Rebuild Cost
How much does a chimney liner cost in Tujunga?
A stainless liner installed in Tujunga typically runs $2,800-$5,200 for a mid-length flue, including insulation and a new cap. Flue size, appliance type, and access move the number within that range. Call (844) 968-2733 for an exact quote. Estimates are free.
Is a chimney rebuild cheaper than a liner replacement?
Usually yes: a partial rebuild ($1,800-$6,500) costs less than a full rebuild ($6,000-$10,000+), and both are larger jobs than a liner install in most cases. The right answer depends on whether the flue or the masonry is failing. An inspection with photos settles it before anyone quotes, and we act on those findings in the same scope. Call (844) 968-2733 for a free estimate.
What does HeatShield resurfacing cost in Tujunga?
HeatShield cast-in-place resurfacing in Tujunga typically costs $1,600-$3,800 for a mid-length flue. It is a less expensive path than a full liner install when the masonry is sound enough to take it. Whether your flue qualifies is a decision for the inspection. Call (844) 968-2733 to get one scheduled.
Why is a full chimney rebuild so expensive?
A full rebuild is the largest line item because it means removing and re-laying masonry from the foundation line of the stack to the top, including new crown, flashing, liner, and cap. In Tujunga that scope typically runs $6,000-$10,000+. Many chimneys quoted a full rebuild elsewhere turn out to need only a partial rebuild ($1,800-$6,500) once inspected properly. Call (844) 968-2733 for a documented second look.
Can you fix a cracked crown or missing cap without a full rebuild?
Yes, in most cases. A crown rebuild ($650-$1,400) and a fitted Gelco or Famco cap ($180-$500) are routine, standalone repairs that often prevent the rebuild in the first place. These are the two most common sources of water intrusion into a chimney. Call (844) 968-2733 to have both priced on one estimate.
Is it cheaper to repair the liner or replace it?
Spot repair is cheaper when the flue is still structurally sound and the damage is limited to isolated sections. When tiles are cracked through or gaps run the length of the flue, a new liner at $2,800-$5,200 is the only repair that holds. The inspection answers this directly. Call (844) 968-2733 for a free estimate.
Can you come today?
Same-day service is often available. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (844) 968-2733 and we will give you the soonest available slot and the full scope in writing.
Why Full-System Chimney Service Matters on a Liner or Rebuild Job
Most chimney work splits into two trades: the sweep who finds the problem and the mason who fixes it. That split is where jobs stall, estimates get lost, and homeowners end up paying twice for access. We built our service around the opposite approach. Inspection, sweeping, crown and cap work, liner install and resurfacing, and both chimney repair and fireplace repair all live in the same scope. When the inspection finds a failed flue tile, the remedy gets priced and scheduled without handing you off.
The material list matters here too. We work with DuraFlex for stainless liner systems, HeatShield for cast-in-place resurfacing, and Gelco, Famco, Olympia Chimney, and Copperfield for components and liner systems. These are the names the trade uses for a reason: sizing standards are consistent, parts are available when a repair needs them, and the installation is documented to a known specification. A generic liner or a hardware-store cap does not carry that.
The crown and cap specialization is worth calling out separately because it is the part of the work that most often gets skipped. In the foothills, a cracked crown on the high side of a roof takes years of rain without anyone noticing until the interior plaster stains. A fitted Gelco or Famco cap closes off the wildlife and water entry point. Doing both correctly extends the life of the liner you just paid for.
Local Neighborhoods We Work In
Tujunga weather is mild, and that has an upside and a downside for chimney work. Mild winters mean the masonry is not under constant freeze pressure, which is good for liner life. But the drier summers and wetter winter storms mean a crown failure on a south-facing stack shows up differently than one on a north-facing slope. We see the same patterns in neighboring foothill and valley neighborhoods, including Sunland-Tujunga, La Crescenta, Glendale, Burbank, Pasadena, Altadena, La Canada Flintridge, and Eagle Rock. If you are in any of these areas and want the liner, crown, or rebuild priced on one estimate, we can do that.
What the Free Estimate Covers
Our estimators do not give a lump-sum number over the phone. The cost depends too much on what the flue and the stack actually look like. The free estimate includes a visual review of the crown, cap, flashing, and visible flue condition, plus a discussion of what the inspection will find once a camera goes in. For jobs that need the full picture, the level 2 inspection is quoted separately at $250-$450 and includes photos you can keep. Every line item on the written estimate is priced. Nothing gets added later without your approval.
Our technicians have up to 9 years of experience on liner installs, resurfacing, crown and cap work, and rebuilding. Between the full system scope and the material lineup, the estimate you get back is what the job actually costs, written in plain terms.
If your chimney has not been looked at since last burning season, or you have seen water staining or a rusted damper, that is the signal to have it inspected before it becomes a liner or rebuild decision. Call (844) 968-2733 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Tujunga market as of 2026. Chimney Sweep Tujunga offers free estimates – call (844) 968-2733.
Written by the team at Chimney Sweep Tujunga.
What Our Customers Say
"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."
- Priya Mehta"Liner was cracked in two places. He walked me through the repair options honestly, including the one that was cheaper for him and better for me."
- Michelle Vaughn"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."
- Carmen Reyes